Braindump2go Free Cisco, Microsoft, CompTIA, VMware, Oracle Exam Questions ,PDF & VCE Dumps Download

[OFFICIAL]Braindump2go 350-080 Dumps Instant Download (31-40)

CISCIO NEW UPDATED: New Updated 350-080 Exam Questions from Braindump2go 350-080 PDF Dumps and 350-080 VCE Dumps! Welcome to Download the Newest Braindump2go 350-080 VCE&PDF Dumps: http://www.braindump2go.com/350-080.html (394 Q&As)

Braindump2go New Released Cisco 350-080 Practice Tests Sample Questions Free Download! 100% Same Questions with Actual 350-080 Exam! Guaranteed 100% Pass!

350-080 Dumps,350-080 Exam Dumps,350-080 Brainfump,350-080 Questions,350-080 VCE,350-080 PDF,350-080 Actual Test,350-080 Study Guide,350-080 Book,350-080 CCIE Data Center Written Exam,350-080 Test

QUESTION 31
Assuming the local peer is 10.0.0.1 and the remote peer (configuration not shown) is 10.0.0.2, which of these is used to configure PIM Anycast-RP on a Nexus 7000 switch?

A.    feature pim
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
B.    feature pim
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 10.0.0.1 2.2.2.2
ip pim anycast-rp 10.0.0.2 2.2.2.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
C.    interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip pim anycast-rp 2.2.2.2 10.0.0.1
ip pim anycast-rp 2.2.2.2 10.0.0.2
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4
D.    feature pim
feature msdp
!
interface loopback1
ip address 10.0.0.1/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
interface loopback2
ip address 2.2.2.2/32
ip router ospf 10 area 0.0.0.0
ip pim sparse-mode
!
ip msdp originator-id loopback1
ip msdp peer 10.0.0.2 connect-source loopback1
ip msdp description 10.0.0.2 To 7010-2
ip msdp password 10.0.0.2 mypassword
!
ip pim rp-address 2.2.2.2 group-list 224.0.0.0/4

Answer: A

QUESTION 32
When using Overlay Transport Virtualization (OTV), how do L2 multicast frames traverse the overlay?

A.    The L2 multicast frames are encapsulated in an OTV packet using the configured control-group
multicast address for transport
B.    The L2 multicast frames are dropped because multicast cannot be carried across the overlay
C.    The L2 multicast frames are encapsulated in an OTV packet using the configured data-group
multicast address for transport
D.    The L2 multicast frames are forwarded natively across the overlay based on their multicast IDs

Answer: C

QUESTION 33
Which three statements best describe multicast operation on Cisco Nexus switches in a data center? (Choose three.)

A.    Cisco NX-OS Software does not support PIM dense mode.
B.    The command ip multicast-routing must be enabled in Cisco NX-OS Software before any multicast
configuration is possible on the switch.
C.    PIM CLI configuration and verification commands are not available until you enable the PIM feature
with the feature pim command.
D.    Cisco NX-OS Software supports multicast routing per Layer 3 VRF instance.
E.    The default PIM operational mode on the Cisco Nexus 7000 switch is SSM.

Answer: ACD

QUESTION 34
On a Cisco Nexus 7000 Series Switch, what is the purpose of this command?
switch# config terminal
switch(config)# mac address-table learning-mode conversational vlan 1-10
switch(config)#

A.    Enable conversational learning on FabricPath vlans 1-10 for F-Series module
B.    Enable FabricPath protocol on VLANs 1?0
C.    No need for this command as conversational learning is enabled by default for all VLANs.
D.    Enable conversational learning on Classical Ethernet VLAN for F-Series module

Answer: D

QUESTION 35
Where is a typical request in the Cisco UCS XML API placed in the data management engine, and, after the request is confirmed, what is updated?

A.    The request is placed in the transactor queue in FIFO order and the management information tree is updated.
B.    The request is placed in the replicator and persistifier and the store is updated.
C.    The request is placed in the data management engine and the application gateway is updated.
D.    The request is placed in the buffer queue and the commit buffer queue is updated.

Answer: A

QUESTION 36
In the Cisco FabricPath domain, one switch becomes the root for the multidestination tree. Cisco FabricPath switches compare which three parameters to select the root? (Choose three.)

A.    Root priority
B.    System ID
C.    Bridge ID
D.    Switch ID
E.    Port ID
F.    Subswitch ID

Answer: ABD

QUESTION 37
By default, what type of SSH server key is generated by Cisco NX-OS Software?

A.    DSA key generated with 512 bits
B.    RSA key generated with 768 bits
C.    RSA key generated with 1024 bits
D.    DSA key generated with 1024 bits
E.    RSA key generated with 2048 bits

Answer: C

QUESTION 38
Refer to the exhibit. Which statements are true about the subswitch ID that is filled in the header? (Choose three.)
A.    FabricPath switches running vPC use this field to identify the specific virtual switch.
B.    FabricPath switches running vPC+ use this field to identify the specific vPC+ PortChannel on which
traffic is to be forwarded.
C.    The subswitch ID field is locally significant to each vPC+ switch pair.
D.    The subswitch ID field must be unique within the FabricPath domain.
E.    In the absence of vPC+, this field is set to 0.

Answer: BCE

QUESTION 39
Refer to the exhibit. vPC+ is configured between which switches?

A.    Switch-ID 13 and Switch-ID 23
B.    Switch-ID 11 and Switch-ID 12
C.    Switch-ID 100 only
D.    Switch-ID 13 and Switch-ID 100

Answer: A

QUESTION 40
In a Cisco Nexus 7000 platform configured with GLBP, which GLBP timer can be tuned to prevent unnecessary GLBP state changes during a switchover or ISSU?

A.    GLBP redirect timer
B.    GLBP forwarder pre-empt delay minimum timer
C.    GLBP hold timer
D.    GLBP pre-empt delay minimum timer
E.    GLBP extended hold timer
F.    GLBP nonstop forwarding timer

Answer: E


100% 350-080 Complete Success & Money Back Guarantee!
By utilizing Braindump2go high quality Cisco 350-080 Exam Dumps Products, You can surely pass 350-080 certification 100%! Braindump2go also offers 100% money back guarantee to individuals in case they fail to pass Cisco 350-080 in one attempt.

FREE DOWNLOAD: NEW UPDATED 350-080 PDF Dumps & 350-080 VCE Dumps from Braindump2go: http://www.braindump2go.com/350-080.html (394 Q&A)